Areas of use

Marine Borda, Deck, Floor Recommended for use in wooden living spaces and superstructures.

Industry:

Recommended for use in offshore environments, refineries, power plants, bridges and buildings. Suitable for use in a wide range of industrial structures. Used as topcoat in pre-approved NORSOK systems. A two-component, chemical curing, aliphatic acrylic polyurethane based topcoat

Approvals and certificates

NORSOK System 1, Rev.5 Wheat certification (Newcastle Occupational Health) Food certification (US compliant, FDA title 21, section 175.300/solid foods) A two-component, chemical curing, aliphatic acrylic polyurethane based paint

When used as part of an approved plan, this material has the following certifications: - Low flame spread in accordance with the European Union Marine Equipment Directive. Approved in accordance with IMO 2010 FTP Code Ch. 8 e in accordance with IMO 2010 FTP Code Annex 1 parts 5 and 2, or IMO FTPC annex 1 parts 5 and 2. 8 e in accordance with IMO 2010 FTP Code Ch. A two-component, chemical curing, aliphatic acrylic polyurethane based paint

Product information

Specifications Test/Standard Description

Solids by volume ISO 3233 63± 2 %

Brightness Degree (GU 60°) ISO 2813 brightness (70-85)

Flash point ISO 3679 Method 1 30 °C

Density approx. 1.4 kg/l

VOC-US/Hong Kong US EPA method 24 (tested) 336 g/l

(CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

VOC-EU IED (2010/75/EU) (theoretical) 336 g/l

Film thickness for each layer

Recommended typical specification range

Dry film thicknesses 50- 100 µm

Wet film thicknesses 80 -160 µm

Theoretical Spread Rate 12.6 -6.3 m2/

In order to achieve full coverage of bright colors, it may be necessary to apply a film thickness at the upper end of the recommended specification range. A two-component, chemical curing, aliphatic acrylic polyurethane based paint

Special effect colors have a variable specification range. For additional information refer to the Application Guide (AG) or contact your nearest polymex chemical office.

Surface Preparation

In order to maintain the adhesion level, the surface of the previous paint coat must be clean, dry and free from any contamination.

Summary table of surface preparation

Surface Minimum Recommended

Painted surfaces Clean dry and undamaged compatible paint Clean dry and undamaged compatible paint

(ISO 12944-4 6.1.4) (ISO 12944-4 6.1.4)

Application Application Methods

The product can be applied with the following equipment:

Spray Use air or airless spray method.

Brush: Brush is recommended for cutting and small areas. Care should be taken to achieve the specified dry film thickness.

A two-component, chemical curing, aliphatic acrylic polyurethane based paint

Roll Can be used. Care should be taken to achieve the specified dry film thickness.

Technical Data Sheet (by volume)

Mixing Ratio (by volume)

A-Comp : 10 units

B-Comp : 1 unit

Guidelines for pneumatic spraying

Nozzle type : 11-19 (HVLP) / 1.1-1.9 mm (pressure vessel)

Pressure at the nozzle (lowest) : 2.1 bar/30 psi (HVLP) / 2.1 bar/30 psi (pressure vessel

Basic values for airless spray application

Breast type (inch/1000): 13-19

Pressure at the nozzle (lowest): 150 bar/2100 psi

Drying and curing times

Surface temperature 5 °C 10 °C 23 °C 40 °C

Surface Drying 16 hours 6 hours 3.5 hours 2 hours

Hard drying 24 hours 14 hours 7 hours 4 hours

Overcoat application, minimum 24 hours 14 hours 7 hours 4 hours

Full curing/commissioning time 21 days 14 days 7 days 3 days

For maximum overcoat application time information, refer to the product application procedure.

Kuruma ve kürlenme süreleri, kontrollü sıcaklık ve %85’in altındaki bağıl nemde ve ürünün uygulanabilir kuru film kalınlığı aralığındaki averaj değerlere göre tespit edilmiştir.

Surface (tactile) dryness: refers to the level of dryness that does not leave marks or reveal stickiness when lightly pressed with a finger.

Hard drying: the minimum time that should be allowed to allow normal foot traffic without any physical damage or permanent marks.

Overcoat, minimum: The minimum time to wait before applying the next coat.

Full cure/service time: the minimum time that must be allowed before the paint system can be permanently exposed to the intended working conditions.

It is a two-component, chemical curing, aliphatic acrylic polyurethane based paint. It is a topcoat product with very good gloss resistance. It has a high solid content. It has low dusting level and good application properties. It is used as a topcoat in structures exposed to atmospheric conditions.

Mix pre-hold time and mix life

Paint temperature : 23 °C 40 °C

Mixture Life : 1.5 hours 50 min

Heat resistance

Dry, atmospheric : 120°C

Maximum temperature exposure time 1 hour maximum.

The specified temperatures are related to the preservation of corrosive properties. Aesthetic properties may deteriorate at these temperatures.

Product compatibility

Depending on the conditions to which the paint system is exposed, various primers and topcoats can be applied compatible with this product. Some of these are listed below. Please contact polymex for specific paint system recommendations.

Previous paint coat: epoxy, zinc epoxy, mastic epoxy, polyurethane

Warning

This product is for professional use only. Applicators and operators must be trained, experienced, competent and equipped to mix and apply the product in accordance with Polymex technical documentation. Applicators and operators must wear appropriate personal protective equipment when using this product. This technical document is based on current product information. Proposed modifications for adjustments to suit site conditions must be submitted to the relevant polymex authority for approval prior to commencement of work. It is a two-component, chemical curing, aliphatic acrylic polyurethane based paint. It is a topcoat product with very good gloss resistance. It has a high solid content. It has low dusting level and good application properties. It is used as a topcoat in structures exposed to atmospheric conditions.

Health and Safety

Please pay attention to the warnings on the packaging. Use under good ventilation conditions. Avoid contact with skin. In case of skin contact, clean immediately with suitable cleanser, soap and water. In case of eye contact, flush eyes with plenty of water and seek medical attention.

Color variability

Occasionally, primers or antifouling paints used primarily as a first coat may show slight color shade variations from pot to pot. When such products are exposed to atmospheric conditions and sunlight, discoloration and chalking may occur.

Legal Notice

The information in this document is based on Polymex laboratory tests and field experience. Polymex products are considered as semi-finished products, but only the quality of the product is guaranteed, as it may be used in situations beyond Polymex control. Some modifications may be made to the product to meet local regulations and market requirements.Polymex reserves the right to change published information without prior notice.

Users should always seek guidance on their needs and specific applications.

Polymex should be consulted. If there is any inconsistency between the different language versions of this document, the English (UK) version shall prevail.

A two-component, chemical curing, aliphatic acrylic polyurethane based paint

Polymex-2026-Dual Component Chemical Resistant Paint

This technical data sheet supersedes all previously published ones. It is recommended to read the Technical Data Sheet (TDS) and the Application Guide together with the Safety Data Sheet (SDS) for this product. To contact your nearest Polymex office, please contact www.polymex.com.tr please visit our website.